Gov Reg™ Adjuster Tool

Gov Reg™ Adjuster Tool

Product Code:G5550
Availability:In Stock
Price: $34.95
Qty:     - OR -   Add to Wish List Add to Compare

1.  Turn off gas supply to the Gov Reg™

2.  Remove the Gov Reg™ from the keg coupler. 

3.  Attach the Gov Reg™ to the Adjuster Tool. 

4.  Turn on gas supply.

5.  Turn handle on tool to adjust pressure setting up or down.

6.  Turn off gas supply.

7.  Reattach the Gov Reg™ to the keg coupler.

8.  Turn on gas supply.  

 

9.  Tap keg.

Gov Reg™

connects here

 

1.  Assuming the Gov Reg™ is already connected to the draught system, turn off the CO2 gas line attached to        the Gov Reg™.

 

2.  Un-thread the coupler nut and remove the Gov Reg™ from the coupler, exposing the adjusting end of the          Gov Reg™.

 

3.  Connect the Adjuster Tool to the exposed end of the Gov Reg™ using the coupler nut and black neoprene          washer until snug.

 

4.  Turn the CO2 gas on, and observe the current pressure on the gauge.

 

​5.  Push in on the Adjuster Tool knob handle and turn slightly until the tool seats into the adjustment cap of the      Gov Reg™.  Keep inward pressure on the knob handle to keep tool properly seated.

 

6.  To adjust pressure, turn the knob in small increments (clockwise to increase pressure and counter-clockwise      to decrease pressure).  After making a small adjustment, depress and release the pressure relief button and      read the new pressure.  Repeat this step until the desired pressure is achieved.

 

7.  Disconnect the Adjuster Tool and ensure the Thomas backflow valve is present in the keg coupler and the          proper beer washer is in place.  

 

8.  Re-install the Gov Reg™ onto the keg coupler by threading the coupler nut back onto the keg coupler.

1.  Turn off gas supply to the Gov Reg™

2.  Remove the Gov Reg™ from the keg coupler. 

3.  Attach the Gov Reg™ to the Adjuster Tool. 

4.  Turn on gas supply.

5.  Turn handle on tool to adjust pressure setting up or down.

6.  Turn off gas supply.

7.  Reattach the Gov Reg™ to the keg coupler.

8.  Turn on gas supply.  

 

9.  Tap keg.

Gov Reg™

connects here

 

1.  Assuming the Gov Reg™ is already connected to the draught system, turn off the CO2 gas line attached to        the Gov Reg™.

 

2.  Un-thread the coupler nut and remove the Gov Reg™ from the coupler, exposing the adjusting end of the          Gov Reg™.

 

3.  Connect the Adjuster Tool to the exposed end of the Gov Reg™ using the coupler nut and black neoprene          washer until snug.

 

4.  Turn the CO2 gas on, and observe the current pressure on the gauge.

 

​5.  Push in on the Adjuster Tool knob handle and turn slightly until the tool seats into the adjustment cap of the      Gov Reg™.  Keep inward pressure on the knob handle to keep tool properly seated.

 

6.  To adjust pressure, turn the knob in small increments (clockwise to increase pressure and counter-clockwise      to decrease pressure).  After making a small adjustment, depress and release the pressure relief button and      read the new pressure.  Repeat this step until the desired pressure is achieved.

 

7.  Disconnect the Adjuster Tool and ensure the Thomas backflow valve is present in the keg coupler and the          proper beer washer is in place.  

 

8.  Re-install the Gov Reg™ onto the keg coupler by threading the coupler nut back onto the keg coupler.

1.  Turn off gas supply to the Gov Reg™

2.  Remove the Gov Reg™ from the keg coupler. 

3.  Attach the Gov Reg™ to the Adjuster Tool. 

4.  Turn on gas supply.

5.  Turn handle on tool to adjust pressure setting up or down.

6.  Turn off gas supply.

7.  Reattach the Gov Reg™ to the keg coupler.

8.  Turn on gas supply.  

 

9.  Tap keg.

Gov Reg™

connects here

 

1.  Assuming the Gov Reg™ is already connected to the draught system, turn off the CO2 gas line attached to        the Gov Reg™.

 

2.  Un-thread the coupler nut and remove the Gov Reg™ from the coupler, exposing the adjusting end of the          Gov Reg™.

 

3.  Connect the Adjuster Tool to the exposed end of the Gov Reg™ using the coupler nut and black neoprene          washer until snug.

 

4.  Turn the CO2 gas on, and observe the current pressure on the gauge.

 

​5.  Push in on the Adjuster Tool knob handle and turn slightly until the tool seats into the adjustment cap of the      Gov Reg™.  Keep inward pressure on the knob handle to keep tool properly seated.

 

6.  To adjust pressure, turn the knob in small increments (clockwise to increase pressure and counter-clockwise      to decrease pressure).  After making a small adjustment, depress and release the pressure relief button and      read the new pressure.  Repeat this step until the desired pressure is achieved.

 

7.  Disconnect the Adjuster Tool and ensure the Thomas backflow valve is present in the keg coupler and the          proper beer washer is in place.  

 

8.  Re-install the Gov Reg™ onto the keg coupler by threading the coupler nut back onto the keg coupler.

http://www.legacyprt.com/adjuster-tool.html

Write a review



Note: HTML is not translated!

Bad           Good



Related Products (1)